How to Find Out What Your Appliances Cost to Run

An electricity bill gives you one number for the whole home, which makes it hard to see which device is actually costing you money. You do not need special skills to work it out. For almost any plug-in appliance, the cost to run it comes from three things: how many watts it draws, how many hours you use it, and what you pay for each unit of electricity. This guide walks through the arithmetic step by step, with practice numbers, and ends with a table you can fill in for your own home.

In brief: Watts × hours ÷ 1,000 gives kilowatt-hours (kWh). kWh × your price per kWh gives cost. The wattage printed on an appliance is usually its maximum, so treat the result as an estimate, and use a plug-in watt meter if you want a better number.

The three formulas

The U.S. Department of Energy (DOE) gives the same three steps in its guide to estimating appliance and home electronics energy use. They are the whole method.

The method

Daily kWh = (watts × hours used per day) ÷ 1,000

Yearly kWh = daily kWh × days used per year

Yearly cost = yearly kWh × your price per kWh

Dividing by 1,000 converts watt-hours into kilowatt-hours, the unit your electricity company bills in. A 1,000-watt device running for one hour uses 1 kWh.

Step by step

  1. Find the watts. Look for a label or nameplate on the back, bottom or side of the appliance, or in its manual. If the label lists only amps, multiply amps by volts to get watts; DOE's example is a shredder rated at 3 amps on a 120-volt supply, which comes to 360 watts. Use the voltage that applies in your country.
  2. Estimate the hours. Think about a normal day. A lamp that is on from dinner until bedtime might run three hours; a router that is never switched off runs 24. Be honest rather than hopeful, because this number matters as much as the watts.
  3. Work out kWh. Multiply watts by hours, then divide by 1,000. For a yearly figure, multiply the daily kWh by the number of days you use the device in a year.
  4. Find your price per kWh. Your bill shows it, or you can divide the energy charge by the kWh used. Check which unit your bill uses: in many places a billed “unit” is one kWh, but confirm on your own bill. Some utilities use tiered rates, so the price may not be one single number; use the rate that applies to the extra electricity you are asking about.
  5. Multiply. Yearly kWh times your price gives the yearly cost. Divide by 12 for a rough monthly figure.

Practice examples

The devices and numbers in the table below are invented for practice. They are not measurements, and they use a made-up price of 10 per kWh in whatever currency you pay in. Replace the price with yours.

Example device (made-up numbers)WattsHours per daykWh per daykWh per yearCost per year at 10 per kWh
Wi-Fi router, always on12240.288105.121,051.20
Lamp, 3 hours a day6030.1865.70657.00
Fan, 8 hours a day5080.40146.001,460.00
Electric kettle, 15 minutes a day in total1,5000.250.375136.881,368.75

Look at the last two rows. The kettle draws thirty times the power of the fan, yet costs about the same over a year in this example, because it runs for a fraction of the time. A high-wattage device used briefly and a low-wattage device used for hours can end up in the same place. That is the main reason to do the arithmetic instead of guessing from the label.

For a real-world reference, DOE works through an electric kettle rated at 1,500 watts used one hour a day: 1.5 kWh a day, 547.5 kWh a year, and at DOE's example price of 11 cents per kWh, about $60 a year. DOE's other example, a paper shredder used a quarter of an hour on 52 days a year, comes to less than a dollar. The same formulas gave both answers.

Devices that switch on and off by themselves

The method above assumes a device draws its rated power the whole time you count. A refrigerator does not: its compressor cycles on and off to hold the temperature, so it runs for only part of the time it is plugged in. DOE suggests a rule of thumb of dividing the plugged-in hours by three to estimate the hours at full wattage. This is a rough guide, not a measurement.

Practice example with invented numbers: a fridge label says 150 watts. Plugged in for 24 hours, that is about 8 hours at full power (24 ÷ 3). Then 150 × 8 ÷ 1,000 = 1.2 kWh a day. A watt meter left on the fridge for a full day or longer will give you a real figure for your own model, in your own kitchen.

Where this method can mislead you

  • The label is a maximum. DOE notes that the wattage on an appliance is the most power it can draw. A fan on a low speed, or a TV at lower brightness, uses less. Your estimate from the label is therefore an upper limit for many devices.
  • Settings change the answer. DOE gives the example that a fan on a higher speed uses more power than one on a lower speed. If you use a device at several settings, work out each one separately.
  • Standby power is invisible. Many devices keep drawing a little power when switched off. A watt meter can show it, and unplugging the device or switching off a power strip stops it. Do not unplug anything that must stay on, such as medical equipment, alarms or, in most homes, the refrigerator.
  • Your hours are a guess. Keep a rough log for one week if the result matters to you. Most people overestimate time for some devices and forget others entirely.
  • Price is not always one number. If your rate is tiered or changes by time of day, the cost of one more kWh may differ from your average.

Get a better number with a watt meter

DOE describes a usage monitor, often called a plug-in watt meter, as the more reliable way to measure a device: you plug the meter into the wall socket, plug the appliance into the meter, and read the watts. Some meters can also estimate cost if you enter your price per kWh. Check the meter's manual before use, because many are made only for ordinary wall-socket devices and cannot be used with large appliances on dedicated or higher-voltage circuits. Prices and models vary by country, so look for one that suits your plug type and voltage.

Safety first: Never open an appliance, remove its cover or change its wiring to measure it. Do not plug a device into a meter that is rated for less power than the device draws. Do not daisy-chain extension leads or power strips. Do not unplug or switch off medical equipment, smoke or security alarms, or in most homes the refrigerator and freezer.

Your own worksheet

Copy this table onto paper or into a spreadsheet and fill it in for five devices you suspect use the most. Use the label or a watt meter for the watts, and your own price per kWh from your bill. The empty cells are for your real numbers.

DeviceWattsHours per daykWh per daykWh per yearCost per year
      
      
      
      
      

When you have finished, add up the yearly kWh column and compare it with the yearly total on your bills. The devices you listed will rarely add up to the whole bill, because heating, cooling, hot water and many small loads are also in there. The point of the exercise is to rank your devices, so you know where a change in habit is worth the effort and where it is not.

Sources

Checked on 17 October 2026. Prices and ratings vary by home and country; the example numbers above are invented for practice.

  • U.S. Department of Energy, Estimating Appliance and Home Electronic Energy Use (Energy Saver): the three formulas, the amps × volts step, the statement that the label wattage is the maximum, the fan-speed example, the refrigerator rule of thumb, the description of usage monitors, and the kettle and shredder examples at 11 cents per kWh.

How this article was prepared: it was drafted with AI assistance, and each factual claim was checked against the sources listed above. The author is Rohan Rawat.

Comments

Popular posts from this blog

12 No-Cost Ways to Lower Your Electricity Use at Home

How to Read a Light Bulb Box: Lumens, Watts and Color